Manufacturing Calcium Phosphates Scaffolds Using 3D-Printed Lost Molds

first_page settings Order Article Reprints Font Type: Arial Georgia Verdana Font Size: Aa Aa Aa Line Spacing:    Column Width:    Background: Open AccessAbstract Manufacturing Calcium Phosphates Scaffolds Using 3D-Printed Lost Molds † by Miguel Albardeiro 1, Adriana Sousa 1, Mafalda Guedes 1,2, Rosa Marat-Mendes 1,3,4, Célio Pina 1,2, Lígia Figueiredo 5, Eduardo Ascenso 5 and Ricardo Baptista 1,3,* 1 CDP2T—Centro de Desenvolvimento de Produto e Transferência de Tecnologia, Escola Superior de Tecnologia de Setúbal, Campus IPS, 2914-503 Setúbal, Portugal 2 CeFEMA—The Center of Physics and Engineering of Advanced Materials, Instituto Superior Técnico (IST), Universidade de Lisboa (UL), 1049-001 Lisboa, Portugal 3 IDMEC—Instituto de Engenharia Mecânica, Instituto Superior Técnico (IST), Universidade de Lisboa (UL), 1049-001 Lisboa, Portugal 4 ENIDH—Escola Náutica Infante D. Henrique, 2770-058 Paço de Arcos, Portugal 5 BioCeramed, 2660-360 São Julião do Tojal, Portugal * Author to whom correspondence should be addressed. † Presented at the Materiais 2022, Marinha Grande, Portugal, 10–13 April 2022. Mater. Proc. 2022, 8(1), 138; https://doi.org/10.3390/materproc2022008138 Published: 21 July 2022 (This article belongs to the Proceedings of MATERIAIS 2022) Download Download PDF Download PDF with Cover Download XML Download Epub Versions Notes Bone tissue engineering (BTE) is centered around the fabrication of scaffolds for the active treatment of large, critical-sized bone defects. Consisting of porous structures of different sizes and shapes, scaffolds allow for cell attachment and growth, while stimulating tissue regeneration and supporting the applied mechanical loads. Scaffolds can be fabricated using different materials, such as metals, polymers and ceramics. Porous metal structures are difficult to manufacture and generate permanent rigid structures, which can lead to stress shielding. Biocompatible polymers can be used to manufacture porous scaffolds with controlled porosity and pore shape. While some polymers are resorbable, they can be difficult to fully metabolize after degradation. Their mechanical properties can be tailored, but a low porosity is required to achieve trabecular bone compatibility. Finally, ceramics are chemically and structurally similar to bone, and also display similar mechanical properties. However, they can be difficult to manufacture into porous structures with controlled porosity.In this paper, an innovative method for producing ceramic scaffolds, with controlled porosity and pore shape, was developed. The lost molds of the scaffolds (10 × 10 × 5 and 10 × 10 × 10 mm) were initially 3D printed in PLA, using a fused filament fabrication (FFF) printer. The pore shape, dimensions and scaffold porosity were controlled using triply periodic minimal surfaces (TPMSs), including primitive and gyroid surfaces. Pore size ranged from 800 to 400 μm, and porosity from 40 to 60%. Scaffold properties can be uniform or graded according to the scaffold height. The pore shape of the scaffolds was also mixed, mimicking bone trabecular distribution. Both hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) suspensions were produced, and their rheological properties analyzed. When their properties were optimized, they were cast into the molds. In the third step, the molds were eliminated, and the scaffolds were sintered using an appropriate thermal cycle.Scaffold characterization included porosity determination, using the Archimedes method, morphology analysis, and scanning electron microscopy (SEM), and the determination of mechanical properties, using compression testing. The produced scaffolds displayed properties that were compatible with trabecular bone replacement. These could be tailored by controlling scaffold porosity and pore shape, including along the load application direction. This manufacturing process allows for pore shape and porosity control thanks to the nature of the TPMS structures. Author ContributionsM.A. and A.S.: experimental work and data analysis; M.G., R.M.-M., C.P., L.F. and E.A.: data analysis and review; R.B.: editing, review and management. All authors have read and agreed to the published version of the manuscript.FundingIPS internal exploration project BioScaff.Institutional Review Board StatementNot applicable.Informed Consent StatementNot applicable.Data Availability StatementNot applicable.Conflicts of InterestThe authors declare no conflict of interest.Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. © 2022 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/). Share and Cite MDPI and ACS Style Albardeiro, M.; Sousa, A.; Guedes, M.; Marat-Mendes, R.; Pina, C.; Figueiredo, L.; Ascenso, E.; Baptista, R. Manufacturing Calcium Phosphates Scaffolds Using 3D-Printed Lost Molds. Mater. Proc. 2022, 8, 138. https://doi.org/10.3390/materproc2022008138 AMA Style Albardeiro M, Sousa A, Guedes M, Marat-Mendes R, Pina C, Figueiredo L, Ascenso E, Baptista R. Manufacturing Calcium Phosphates Scaffolds Using 3D-Printed Lost Molds. Materials Proceedings. 2022; 8(1):138. https://doi.org/10.3390/materproc2022008138 Chicago/Turabian Style Albardeiro, Miguel, Adriana Sousa, Mafalda Guedes, Rosa Marat-Mendes, Célio Pina, Lígia Figueiredo, Eduardo Ascenso, and Ricardo Baptista. 2022. "Manufacturing Calcium Phosphates Scaffolds Using 3D-Printed Lost Molds" Materials Proceedings 8, no. 1: 138. https://doi.org/10.3390/materproc2022008138 Find Other Styles Note that from the first issue of 2016, MDPI journals use article numbers instead of page numbers. See further details here. Article Metrics No No Article Access Statistics Multiple requests from the same IP address are counted as one view.